Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Just how do you actually feel with regards to How to Install a Bathtub?
Installing a bathtub isn't specifically brain surgery, but it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult job. If the old bathtub is easily accessible, the job can move easily; if you have to open a wall surface to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make certain you have actually certified yourself for the task and also are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already purchased a new bathtub and also do not need to transform the arrangement of your previous water pipelines.
Your tools and material checklist need to comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain any water continuing to be in the system. The process of removing the existing taps can be rather troublesome because of the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Secure the tap in position with the supplier supplied backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Using the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub up until the level checks out level.
To set up faucets, fit all-time low of the outermost flexible tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if required. Fill up the bath tub as well as also check the overflow outlet and the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been utilized at the very least when as this will settle it into its final position.
Preparing for the Installation
Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to stop stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall between the bathroom and also the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack rather very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly available on the market. It is advisable to fit the tiles making use of waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about Installing A Bathtub? Create a comment down below. We'd be glad to find out your ideas about this article. Hoping to see you back again in the future. Please take the opportunity to promote this content if you enjoyed reading it. I praise you for your time. Don't forget to visit our website back soon.
Free Estimate Report this page